View AWC6323_6167944.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AWC6323 help3e tm dual-band cellular & pcs cdma 3.4 v linear power amplifer module data sheet - rev 2.2 m47 package 14 pin 3 mm x 5 mm x 1 mm surface mount module features ? ingap hbt technology ? high effciency (cell band): ? 37.5 % @ p out = +27.6 dbm ? 23 % @ p out = +16 dbm ? 11.5 % @ p out = +10 dbm ? low quiescent current: 3.5 ma ? internal voltage regulation ? built-in directional coupler ? common v mode control line ? simplifed v cc bus pcb routing ? reduced external component count ? low profle surface mount package: 1 mm ? rohs compliant package, 260 o c msl-3 applications ? cell & pcs dual-band wireless handsets and data devices for cdma/evdo networks. product description AWC6323 addresses the demand for increased integration in dual-band handsets for cdma networks. the small footprint 3 mm x 5 mm x 1 mm surface- mount rohs compliant package contains independent rf pa paths to ensure optimal performance in both frequency bands, while achieving a 25% pcb space savings compared with solutions requiring two single-band pas. the package pinout was chosen to enable handset manufacturers to easily route bias to both power amplifers and simplify control with common mode pins. the device is manufactured on an advanced ingap hbt mmic technology offering state-of-the-art reliability, temperature stability, and ruggedness. the AWC6323 is part of anadigics high-effciency-at-low-power (help?) family of cdma power amplifers, which deliver low quiescent currents and signifcantly greater effciency without the need of an external dc-dc converter. through selectable bias modes, the AWC6323 achieves optimal effciency, specifcally at low- and mid-range power levels where the pa typically operates, thereby dramatically increasing handset talk-time. its built-in voltage regulator eliminates the need for external switches. this pa has built-in directional couplers for each band, with a common coupler output port cpl_out. the 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, effciency and linearity in a 50 ? system. figure 1: block diagram a wc6323 v en_cell v batt rf in_cell rf out_cell v cc a v mode1 1 13 11 14 12 3 4 2 gnd v cc 5 6 10 9 bias control voltage regulation cpl out rf out_pcs v en_pcs rf in_pcs gnd at slug (pad) 8 7 v mode2 gnd bias control voltage regulation cpl cpl 03/2012
2 table 1: pin description figure 2: pinout v mode1 v mode2 cpl out pin name description 1 v en_cell enable voltage for cell band 2 rf in_cell rf input for cell band 3 v mode1 mode control voltage 1 4 v batt battery voltage 5 v mode2 mode control voltage 2 6 rf in_p c s rf input for pcs band 7 v en_pcs enable voltage for pcs band 8 rf out_pcs rf output for pcs band 9 gnd ground 10 cpl out coupler output port 11 v cc a battery voltage a 12 v cc supply voltage 13 rf out_cell rf output for cell band 14 gnd ground data sheet - rev 2.2 03/2012 AWC6323
3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operation at v cc = +3.2 v, p out is derated by 0.5 db. parameter min max unit supply voltage (v batt , v cc , v cc a) 0 +5 v mode control voltage (v mode1, v mode2 ) 0 +3.5 v enable voltage (v en_cell , v en_pcs ) 0 +3.5 v rf input power (p in ) - +10 dbm storage temperature (t stg ) -40 +150 c parameter min typ max unit comments operating frequency (f) 824 1850 - 849 1910 mhz cellular pcs supply voltage (v cc and v batt ) +3.2 +3.4 +4.2 v enable voltage (v en ) +1.35 0 +1.8 - +3.1 +0.5 v pa "on" pa "shut down" mode control voltage (v mode1, v mode2 ) +1.35 0 +1.8 - +3.1 +0.5 v high state voltage low state voltage cellular rf output power (p out ) cdma, hpm cdma, mpm cdma, lpm +27.1 (1) - - 27.6 16 10 - - - dbm cdma 2000, rc-1 pcs rf output power (p out ) cdma, hpm cdma, mpm cdma, lpm +27.4 (1) - - +27.9 16 10 - - - dbm cdma 2000, rc-1 case temperature (t c ) -30 - +90 c data sheet - rev 2.2 03/2012 AWC6323
4 table 4a: electrical specifcations - cellular band (bc 0) (t c = +25 c, v batt = v cc = +3.4 v, v en_cell = +1.8 v, 50 ? system, cdma2000 rc-1 waveform) parameter min typ max unit comments v mode1 v mode2 p out dl 14 8 30 19 14 0 v 1.8 v 9 1.8 v 1.8 v 0 v p p p mdfh&dho3rhu at ? ? - - - f 0 v 1.8 v 9 1.8 v 1.8 v 0 v p p p mdfh&dho3rhu at ? ? - - - f 0 v 1.8 v 9 1.8 v 1.8 v 0 v p p p 3rhuhlflhf 34 18 8 23 - - - 0 v 1.8 v 9 1.8 v 1.8 v 0 v p p p 4lhvfh&uuhft - ma ur9 cc slv v mode1 99 mode2 = 0 v mode control current - 0.1 ma ur9 mode slv v mode1 99 mode2 = 0 v dhu&uuh - 1 2 ma ur9 sl9 mode1 9 v mode2 = 0 v enable current - <0.1 ma ur9 1& pin 1rlvhlhfhlhd - -133 -138 -131 p+ v mode1 99 mode2 9 v mode1 = v mode2 = 1.8 v +duprlfv r rr - - -43 -30 -30 f p o u t < p spshdfh - - 9 &rsoldfru - 22 - data sheet - rev 2.2 03/2012 AWC6323
5 table 4b: electrical specifcations - cellular band (bc 0) (t c = +25 c, v batt = v cc = +3.4 v, v en_cell = +1.8 v, 50 system, cdma2000 rc-1 waveform) notes: (1) pae and acp measured at 836.5 mhz. (2) 869 mhz to 894 mhz. p a r a m e t e r m i n t y p m a x u n i t c o m m e n t s v m o d e 1 v m o d e 2 p o u t s p u r i o u s o u t p u t l e v e l ( a l l sp u r i o u s o u t p u t s) - - - 6 5 d b c p o u t < + 2 7 . 6 d b m i n - b a n d l o a d v s w r < 5 : 1 o u t - o f - b a n d l o a d v s w r < 1 0 : 1 a p p l i e s o v e r a l l o p e r a t i n g co n d i t i o n s l o a d m i sm a t ch st r e ss w i t h n o p e r m a n e n t d e g r a d a t i o n o r f a i l u r e 8 : 1 - - v s w r a p p l i e s o v e r f u l l o p e r a t i n g co n d i t i o n s data sheet - rev 2.2 03/2012 AWC6323
6 table 5a: electrical specifcations - pcs band (bc 1) (t c = +25 c, v batt = v cc = +3.4 v, v en_pcs = +1.8 v, 50 system, cdma2000 rc-1 waveform) parameter min typ max unit comments v mode1 v mode2 p out gain 24.5 10 7 26.5 13.5 10 30 16 13 db 0 v 1.8 v 0/1.8 v 1.8 v 1.8 v 0 v +27.9 dbm +16 dbm +10 dbm adjacent channel power at ? 1.25 mhz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 khz - - - -51 -52 -52 -46.5 -46.5 -46.5 dbc 0 v 1.8 v 0/1.8 v 1.8 v 1.8 v 0 v +27.9 dbm +16 dbm +10 dbm adjacent channel power at ? 1.98 mhz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 khz - - - -56 -59 -63 -54 -54 -54 dbc 0 v 1.8 v 0/1.8 v 1.8 v 1.8 v 0 v +27.9 dbm +16 dbm +10 dbm power-added efficiency (1) 33 18 8 36.5 21 11 - - - % 0 v 1.8 v 0/1.8 v 1.8 v 1.8 v 0 v +27.9 dbm +16 dbm +10 dbm quiescent current (icq) - 3.5 6 ma through v batt and v cc pins, v mode1 = 0/1.8 v, v mode2 = 0 v mode control current - 0.05 0.1 ma tthrough v mode pins, v mode1 = 0/1.8 v, v mode2 = 0 v battery current - 1 2 ma through v batt pin, v mode1 = 0/1.8 v, v mode2 = 0 v enable current - <0.1 0.15 ma through v en_cell pin total decoder current on v batt (in shutdown mode) - 7 16 ? a v batt = +4.2 v, v cc = +4.2 v, v en_cell = 0 v, v mode1 = 0 v, v mode2 = 0 v total pa leakage current on v cc (in shutdown mode) - 1 5 ? a v batt = +4.2 v, v cc = +4.2 v, v en_cell = 0 v, v mode1 = 0 v, v mode2 = 0 v noise in receive band (2) - - -133 -137 -131 -134 dbm/hz v mode1 = 0 v, v mode2 = 1.8 v v mode1 = v mode2 = 1.8 v harmonics 2fo 3fo, 4fo - - -41 -50 -30 -30 dbc p o u t < +27.9 dbm input impedance - - 2:1 vswr coupling factor - 22 - db data sheet - rev 2.2 03/2012 AWC6323
7 notes: (1) acprs and effciency measured at 1880 mhz. (2) 1930 mhz to 1990 mhz. deohe(ohfufdo6hffdv36d c = +25 c, v batt = v cc = +3.4 v, v en_pcs ? l o a d m i sm a t ch st r e ss w i t h n o p a r a m e t e r m i n t y p m a x u n i t c o m m e n t s v m o d e 1 v m o d e 2 p o u t s p u r i o u s o u t p u t l e v e l ( a l l sp u r i o u s o u t p u t s) - - - 6 5 d b c p o u t < + 2 7 . 9 d b m i n - b a n d l o a d v s w r < 5 : 1 o u t - o f - b a n d l o a d v s w r < 1 0 : 1 a p p l i e s o v e r a l l o p e r a t i n g co n d i t i o n s p e r m a n e n t d e g r a d a t i o n o r f a i l u r e 8 : 1 - - v s w r a p p l i e s o v e r f u l l o p e r a t i n g co n d i t i o n s data sheet - rev 2.2 03/2012 AWC6323
8 application information to ensure proper performance, refer to all related application notes on the anadigics web site: http://www.anadigics.com shutdown mode the power amplifer may be placed in a shutdown mode by applying logic low levels (see operating ranges table) to the v enable and v mode voltages. table 6: bias control bias modes the power amplifer may be placed in low, medium or high bias modes by applying the appropriate logic level (see operating ranges table) to the v mode1, and v mode2 pins. the bias control table lists the recommended modes of operation for various applications. a p p l i c a t i o n p o u t l e v e l s b i a s m o d e v e n v m o d e 1 v m o d e 2 v c c v b a t t c d m a - l o w p o w e r ( l o w b i a s m o d e ) < + 1 0 d b m l o w + 1 . 8 v - 0 v 3 . 2 - 4 . 2 v > 3 . 2 v c d m a - m e d p o w e r ( m e d i u m b i a s m o d e ) > 8 d b m < + 1 6 d b m m e d + 1 . 8 v + 1 . 8 v + 1 . 8 v 3 . 2 - 4 . 2 v > 3 . 2 v c d m a - h i g h p o w e r ( h i g h b i a s m o d e ) > + 1 6 d b m h i g h + 1 . 8 v 0 v + 1 . 8 v 3 . 2 - 4 . 2 v > 3 . 2 v s h u t d o w n - s h u t d o w n 0 v 0 v 0 v 3 . 2 - 4 . 2 v > 3 . 2 v v en_cell,pcs v cc, v cc a note 1 rf in_cell,pcs notes 1,2 off sequence referenced after 90 % of rise time referenced before 10 % of fall time on sequence on sequence start t_ 0n = 0 t_ 0n +1 s t_ 0n +3 s off sequence start t_ 0f f = 0 t_ 0f f+ 2 st _0 ff +3 s vcontrols venable/vmode(s ) rise/fall max 1 s defined at 10% to 90% of min/max voltage figure 3: recommended on/off timing sequence notes: (1) level might be changed after rf is on. (2) rf off defned as p -30 dbm. (3) switching simultaneously between v is not recommended. data sheet - rev 2.2 03/2012 AWC6323
9 figure 4: application circuit 1 13 11 14 12 3 4 2 5 6 10 9 bias control voltage regulation cpl out gnd at slug (pad) 8 7 bias control voltage regulation cpl cpl rf in_cell rf in_pcs v mode1 v batt v en_cell v en_pcs 2.2 ?f v mode2 68pf v cc 68 pf 1000 pf 2.2 ?f rf out_cell 33 pf rf out_pcs 1000 pf data sheet - rev 2.2 03/2012 AWC6323
10 package outline figure 5: package outline - 14 pin 3 mm x 5 mm x 1 mm surface mount module figure 6: branding specifcation data sheet - rev 2.2 03/2012 AWC6323
11 ordering information order number temperature range package description component packaging AWC6323rm47q7 -30 c to +90 c rohs compliant 14 pin 3 mm x 5 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel AWC6323rm47p9 -30 c to +90 c rohs compliant 14 pin 3 mm x 5 mm x 1 mm surface mount module partial tape and reel warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. import ant notice anadigics, inc. 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.2 03/2012 AWC6323

▲Up To Search▲

Price & Availability of AWC6323

	To Download AWC6323 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .